Shape memory alloy
The following WikiProjects or Portals may be able to help recruit one:WikiProject Technology Technology Portal WikiProject Engineering Engineering Portal
If another appropriate WikiProject or portal exists, please adjust this template accordingly.(February 2009)
The three main types of shape memory alloys are the copper-zinc-aluminum-nickel, copper-aluminium-nickel, and nickel-titanium (NiTi) alloys but SMA's can also be used by alloying zinc, copper, gold, and iron. NiTi alloys are generally more expensive and change from austenite to martensite upon cooling; Mf is the temperature at which the transition to Martensite is finished during cooling. Accordingly, during heating As and Af are the temperatures at which the transformation from Martensite to Austenite starts and finishes. Repeated use of the shape memory effect may lead to a shift of the characteristic transformation temperatures (this effect is known as functional fatigue, as it is closely related with a change of microstructural and functional properties of the material).
The transition from the martensite phase to the austenite phase is only dependent on temperature and stress, not time, as most phase changes are, as there is no diffusion involved. Similarly, the austenite structure gets its name from steel alloys of a similar structure. It is the reversible diffusionless transition between these two phases that allow the special properties to arise. While martensite can be formed from austenite by rapidly cooling carbon-steel, this process is not reversible, so steel does not have shape memory properties.
In this figure, (T) represents the martensite fraction. The difference between the heating transition and the cooling transition give rise to the shape of the curve depends on the material properties of the shape memory alloy, such as the alloying and work hardening
One-way vs. two-way shape memory
Shape memory alloys have different shape memory effects. Two common effects are one-way and two-way shape memory. A schematic of the effects is shown below.
In the figure above, the procedures are very similar: starting from martensite (a), adding a reversible deformation for the one-way effect or severe deformation with an irreversible amount for the two-way (b), heating the sample (c) and cooling it again (d).
One way memory effect
When a shape memory alloy is in its cold state (below As), the metal can be bent or stretched and will hold those shapes until heated above the transition temperature. Upon heating, the shape changes to its original. When the metal cools again it will remain in the hot shape, until deformed again.
With the one-way effect, cooling from high temperatures does not cause a macroscopic shape change. A deformation is necessary to create the low-temperature shape. On heating, transformation starts at As and is completed at Af (typically 2 to 20 C or hotter, depending on the alloy or the loading conditions). As is determined by the alloy type and composition. It can be varied between 150 C and 200 C.
Two way memory effect
The two-way shape memory effect is the effect that the material remembers two different shapes: one at low temperatures, and one at the high temperature shape. A material that shows a shape memory effect during both heating and cooling is called two-way shape memory. This can also be obtained without the application of an external force (intrinsic two-way effect). The reason the material behaves so differently in these situations lies in training. Training implies that a shape memory can "learn" to behave in a certain way. Under normal circumstances, a shape memory alloy "remembers" its high-temperature shape, but upon heating to recover the high-temperature shape, immediately "forgets" the low-temperature shape. However, it can be "trained" to "remember" to leave some reminders of the deformed low-temperature condition in the high-temperature phases. There are several ways of doing this. A shaped, trained object heated beyond a certain point will lose the two way memory effect, this is known as "amnesia".
Pseudo-elasticity
One of the commercial uses of shape memory alloy involves using the pseudo-elastic properties of the metal during the high temperature (austenitic) phase. The frames of reading glasses have been made of shape memory alloy as they can undergo large deformations in their high temperature state and then instantly revert back to their original shape when the stress is removed. This is the result of pseudoelasticity; the martensitic phase is generated by stressing the metal in the austenitic state and this martensite phase is capable of large strains. With the removal of the load, the martensite transforms back into the austenite phase and resumes its original shape.
This allows the metal to be bent, twisted and pulled, before reforming its shape when released. This means the frames of shape memory alloy glasses are claimed to be "nearly indestructible" because it appears no amount of bending results in permanent plastic deformation.
Transition temperature
The martensite start temperature of shape memory alloys at which they function is dependent on a number of factors including alloy chemistry. Shape memory alloys with transformation temperatures in the range of 60-1450 K have been made. Zarinejad and co-workers have recently shown that the martensite start temperature increases with the decrease of the valence electron density (concentration) of these alloys.
History
The first reported steps towards the discovery of the shape memory effect were taken in the 1930s. According to Otsuka and Wayman (1998), A. lander discovered the pseudoelastic behavior of the Au-Cd alloy in 1932. Greninger & Mooradian (1938) observed the formation and disappearance of a martensitic phase by decreasing and increasing the temperature of a Cu-Zn alloy. The basic phenomenon of the memory effect governed by the thermoelastic behavior of the martensite phase was widely reported a decade later by Kurdjumov & Khandros (1949) and also by Chang & Read (1951).
The nickel-titanium alloys were first developed in 19621963 by the US Naval Ordnance Laboratory and commercialized under the trade name Nitinol (an acronym for Nickel Titanium Naval Ordnance Laboratories). Their remarkable properties were discovered by accident. A sample that was bent out of shape many times was presented at a laboratory management meeting. One of the associate technical directors, Dr. David S. Muzzey, decided to see what would happen if the sample was subjected to heat and held his pipe lighter underneath it. To everyone's amazement the sample stretched back to its original shape.
There is another type of S.M.A., called a ferromagnetic shape memory alloy (FSMA), that changes shape under strong magnetic fields. These materials are of particular interest as the magnetic response tends to be faster and more efficient than temperature-induced responses.
Metal alloys are not the only thermally-responsive materials; shape memory polymers have also been developed, and became commercially available in the late 1990s.
Crystal structures
Many metals have several different crystal structures at the same composition, but most metals do not show this shape memory effect. The special property that allows shape memory alloys to revert to their original shape after heating is that their crystal transformation is fully reversible. In most crystal transformations, the atoms in the structure will travel through the metal by diffusion, changing the composition locally, even though the metal as a whole is made of the same atoms. A reversible transformation does not involve this diffusion of atoms, instead all the atoms shift at the same time to form a new structure, much in the way a parallelogram can be made out of a square by pushing on two opposing sides. At different temperatures, different structures are preferred and when the structure is cooled through the transition temperature, the martensitic structure forms from the austenitic phase.
Manufacture
Shape memory alloys are typically made by casting, using vacuum arc melting or induction melting. These are specialist techniques used to keep impurities in the alloy to a minimum and ensure the metals are well mixed. The ingot is then hot rolled into longer sections and then drawn to turn it into wire The way in which the alloys are "trained" depends on the properties
wanted. The "training" dictates the shape that the alloy will remember when it is heated. This occurs by heating the alloy so that the dislocations re-order into stable positions, but not so hot that the material recrystallizes. They are heated to between 400 C and 500 C for 30 minutes. Typical variables for some alloys are 500 C and for more than 5 minutes.
They are then shaped while hot and are cooled rapidly by quenching in water or by cooling with air.
Properties
The copper-based and Ni Ti (nickel and titanium)-based shape memory alloys are considered to be engineering materials. These compositions can be manufactured to almost any shape and size.
The yield strength of shape memory alloys is lower than that of conventional steel, but some compositions have a higher yield strength than plastic or aluminum. The yield stress for Ni Ti can reach 500 MPa. The high cost of the metal itself and the processing requirements make it difficult and expensive to implement SMAs into a design. As a result, these materials are used in applications where the super elastic properties or the shape memory effect can be exploited. The most common application is in actuation.
One of the advantages to using shape memory alloys is the high level of recoverable plastic strain that can be induced. The maximum recoverable strain these materials can hold without permanent damage is up to 8% for some alloys. This compares with a maximum strain 0.5% for conventional steels.
Applications
Industrial
Aircraft
See also: Aircraft
Boeing, General Electric Aircraft Engines, Goodrich Corporation, NASA, and All Nippon Airways developed the Variable Geometry Chevron using shape memory alloy that reduces aircraft's engine noise. All of Boeing's new aircraft will be equipped with this new technology.
Piping
See also: Piping
The first consumer commercial application for the material was as a shape memory coupling for piping, e.g. oil line pipes for industrial applications, water pipes and similar types of piping for consumer/commercial applications. The late 1980s saw the commercial introduction of Nitinol as an enabling technology in a number of minimally invasive endovascular medical applications. While more costly than stainless steel, the self expanding properties of Nitinol alloys manufactured to BTR (Body Temperature Response), have provided an attractive alternative to balloon expandable devices. On average, 50% of all peripheral vascular stents currently available on the worldwide market are manufactured with Nitinol.
Robotics
See also: Robotics
There have also been limited studies on using these materials in robotics (such as "Roboterfrau Lara"), as they make it possible to create very light robots. Weak points of the technology are energy inefficiency, slow response times, and large hysteresis.
Nitinol wire is also used in robotics (e.g. the hobbyist robot Stiquito) and in a few magic tricks, particularly those involving heat and shapeshifting.
Medicine
Optometry
Eyeglass frames made from titanium-containing SMAs are marketed under the trademarks Flexon and TITANflex. These frames are usually made out of shape memory alloys that have their transition temperature set below the expected room temperature. This allows the frames to undergo large deformation under stress, yet regain their intended shape once the metal is unloaded again. The very large apparently elastic strains are due to the stress-induced martensitic effect, where the crystal structure can transform under loading, allowing the shape to change temporarily under load. This means that eyeglasses made of shape memory alloys are more robust against being accidentally damaged.
Orthopaedic surgery
This section is in need of attention from an expert on the subject. WikiProject Medicine or the Medicine Portal may be able to help recruit one. (February 2009)
Memory metal has been utilised in orthopaedic surgery as a fixation device for osteotomies, typically around the foot and ankle. The device, usually a staple, is stored in a refrigerator in its malleable form and is implanted into pre-drilled holes in the bone across an osteotomy. As the staple warms it returns to its non-malleable state and compresses the bony surfaces together to promote union of the osteotomy.
Dentistry
The range of applications for SMAs has grown over the years, a major area of development being medicine. One example is the prevalence of dental braces using SMA technology to exert constant tooth-moving forces on the teeth; the nitinol archwire was developed in 1972 by orthodontist George Andreasen. This revolutionized clinical orthodontics and has also had an effect on fiber optic development. Andreasen's alloy has a patterned shape memory, expanding and contracting within given temperature ranges because of its geometric programming.
Harmeet D. Walia later utilized the alloy in the manufacture of root canal files for endodontics.
Materials
Alloys of metals having the memory effect at different temperatures and at different percentages of its solid solution contents.
Ag-Cd 44/49 at.% Cd
Au-Cd 46.5/50 at.% Cd
Cu-Al-Ni 14/14.5 wt.% Al and 3/4.5 wt.% Ni
Cu-Sn approx. 15 at.% Sn
Cu-Zn 38.5/41.5 wt.% Zn
Cu-Zn-X (X = Si, Al, Sn)
Fe-Pt approx. 25 at.% Pt
Mn-Cu 5/35 at.% Cu
Fe-Mn-Si
Pt alloys
Co-Ni-Al
Co-Ni-Ga
Ni-Fe-Ga
Ti-Pd in various concentrations
Ni-Ti (~55% Ni)
Ni-Mn-Ga
References
^ Shape Memory Materials, K Otsuka, CM Wayman, Cambridge University Press, 1998, http://catdir.loc.gov/catdir/samples/cam034/97036119.pdf
^ Martensitic Transformations and the Shape Memory Effect in Ti50Ni10Au40 and Ti50Au50 Alloys, SK WU AND CM WAYMAN, METALLOGRAPHY 20:359-376 (1987)
^ INFLUENCE OF WORK HARDENING AND HEAT TREATMENT ON THE SUBSTRUCTURE AND DEFORMATION BEHAVIOUR OF TiNi SHAPE MEMORY ALLOYS, P FILTP and K MAZANEC, Scripta Metallurgica et Materialia, Vol. 32. No. 9, pp. 1375-1380. 1995
^ http://www-personal.umich.edu/~btrease/share/SMA-Shape-Training-Tutorial.pdf
^ Kauffman, George, and Isaac Mayo. "Memory Metal." Chem Matters Oct. 1993: 4-7.
^ http://www.wolaa.org/files/Nitinol_Oral_History.pdf, Oral history by William J. Buehler
^ http://www.lararobot.de
^ New York Times obituary of Dr. Andreasen
Further reading
Duerig, TW, KN Melton, D Stckel and CM Wayman. "Engineering Aspects of Shape Memory alloys". ISBN 0-7506-1009-3. London: Butterworth Heinemann, 1990.
K. Shimizu and T. Tadaki, Shape Memory Alloys, H. Funakubo, Ed., Gordon and Breach Science Publishers, 1987
External links
Shape Memory Alloys and Their Applications - Introductory information on Shape Memory Alloys
Nitinol Technical Information (from Johnson Matthey, Inc.)
BBC report on medical applications of Nitinol
SFB 459: A German Research Center for Shape Memory Alloys
SMAterial.com - phenomena, crystallography, model, simulation and applications of SMA - Has .gif animations demonstrating the effect.
Texas A&M University's Shape Memory Alloy Research Team - SMA overview, publications, etc.
Institute of Physics, ASCR - Research Projects, publications, events & conferences, functional materials
Berkeley - Bioeng/ME C117 Structural Aspects of Biomaterials - Video Lecture: Dr. Scott Robertson, Stents: Fatigue and Fracture, LBL - Material properties of Nitinol stents
Berkeley - Bioeng/ME C117 Structural Aspects of Biomaterials - Video Lecture: Dr. Alan Pelton, Stent Design, Nitinol Device Company (NDC) - Material properties of Nitinol stents
SMST Proceedings
some patents and publications to memory alloys (German)
Categories: Alloys | Smart materials | MetallurgyHidden categories: Technology articles needing expert attention | Engineering articles needing expert attention | Articles needing expert attention from February 2009 | All articles needing expert attention | Medicine articles needing expert attention
没有评论:
发表评论